Blog Archives

’57 is up next

DSCF1082DSCF1083DSCF1084 The ’57 is ready for its turn in the booth. The past couple of weeks we have been working on getting it ready for paint and Monday is the day. We have meticulously sanded this vehicle and spent quite a bit of time blowing out all the nooks and crannies where dust can hide. We have changed the booth filters and washed it down. Monday we will finish prepping the booth and finish masking off the car. We will start by applying a coat of sealer over the entire car. We will then paint the roof white and when that is dry, we will mask it off and paint the body the Tropical Turquoise. We will then follow that up with 3 coats of PPG’s 2021 high solids clear. Its been a long while coming but this ’57 will be looking good again in a few more days.

Advertisements

A little shiny work from this week

DSCF1069DSCF1066DSCF1067DSCF1068The owner of this 2003 Silverado wanted to freshen things up a bit. He bought the truck new and since it still ran great but looked bad he decided to paint it. After discussing his options we came up with a plan and got to work. We started by removing the lights, bumpers, handles, moldings and mirrors. We then sanded the whole truck down and fixed the very few small dents that it had. We then washed it a couple of times to make sure we had a clean truck, clean jambs and clean engine bay. We then masked off the ares that were not getting paint and started spraying. A few coats of  PPG black followed by a couple coats of PPG’s high solids clear coat and we have very nice Silverado that shines better than new.

Cab’s on deck

DSCF1062DSCF1063DSCF1064Although we haven’t posted in a while on our restoration projects, we have worked on them some. Here is the cab on the C-10 that we have been working on. We started with the bed a couple of months ago and now we are onto the cab. As you can see its already in epoxy primer and we have started some body work. We did find a few too many pin holes to repair in the left and right floor pans so we will go ahead and replace them in a week or so. We have gotten a start on the body repairs in the meantime. Keep an eye out for this one. Its going to be a real head turner.

 

Time for bed

DSCF1029DSCF1030DSCF1031DSCF1032DSCF1033DSCF1041DSCF1040DSCF1042DSCF1043DSCF1044DSCF1045We have been working pretty hard and heavy on the the C-10 these past few weeks and its paying off. The hood is completely finished and ready for paint. The next time it gets sanded, it will be painted.  The body work on the outside of the bedsides are done and in their second priming. We will block those out one more time and prime them once more to ensure they are straight. The body work on the inside of the bedsides was finished up today and they were primed as well. All in all, quite a bit of work getting done on this one. Next we finish the outsides of the beds then its on to the cab and doors.

Straightening the curves

DSCF1024DSCF1022DSCF1023DSCF1021DSCF1020DSCF1028DSCF1027DSCF1026DSCF1025Now that the outside of the bedsides are straight, its time for the insides. Same steps here as the outsides. Block out the primer to find the highs and lows, tap the highs down and fill the lows. Since this truck is 45 years old, it has some wear and tear. We are going to go ahead and also fill the pitting that has occurred from years of use along with the spot welds to make the insides of these smooth as silk. Its little things like that that make it a little different than the others.

Bed liner and hood primer

DSCF1001DSCF1002DSCF1004DSCF1005DSCF1003 Read the rest of this entry

Its a block party!

DSCF0988DSCF0987DSCF0986DSCF0985DSCF0984DSCF0997DSCF0998DSCF0979DSCF0980DSCF0981DSCF0982DSCF0995DSCF0994DSCF0992DSCF0990 In the words of Ice Cube, today was a good day. Lots of body work was completed on the quarters, the bottom of the  hood and bottom portion of the bed floor was sprayed with epoxy. Once the epoxy was dry the bed floor was sprayed with bed liner. Tomorrow we plan on flipping the bed floor over, spraying epoxy on it and bed lining it as well. We will also spray the top side of the hood with high build epoxy and I hope to re-prime the bedsides. Its a tall order but we are really close to finishing up the body work on the bedsides.

Let the fun begin

DSCF0976DSCF0977DSCF0972DSCF0973DSCF0974DSCF0969DSCF0978DSCF0970DSCF0971DSCF0975Here you can see we have gotten started on the bodywork on the ’71 C10. This truck will be restoration with a few twists to make it more fun to drive and look better than when it was new. Paul worked on sanding the bottom of the bed in preparation for its epoxy coating followed by Raptor liner bed liner. The top side will also receive the same treatment. While Paul was working on that, Jordan and I was straightening out the bedsides. This truck has seen its days as a work truck. The beds are not in horrible shape but do need quite a bit of straightening out. All the molding holes have already been welded up as well as the side marker lights. These areas must now be straightened. We primed these panels a few weeks ago using PPG’s Vibrance line of high build epoxy. We then blocked the bedsides out with 80 grit sandpaper and started the body work you see here. Once the outsides of these bedsides are straight, we will prime these 2 more times to be sure they are nice and straight. This will ensure a slick paint job that you can also use as a mirror. Cole worked the hood over really good. Cleaning the pits of rust out and sanding it so we can apply epoxy to it as well. We also metal worked the hood out at this time to minimize filler. Tomorrow we plan on spraying some primer and bedliner so stay tuned.

Bed time

DSCF0927DSCF0928DSCF0933DSCF0934DSCF0936DSCF0935DSCF0938DSCF0941DSCF0942DSCF0943DSCF0945DSCF0944 Over the past few days we have been working on the C10 project, you may have seen the first post a few weeks back. We decided to blow this bed back apart to make sure we get paint and primer in all the nooks and crannies. It hard enough to do apart but together its impossible. We also welded in a patch in an ugly area on the inside lip of the bed rail. Looks like someone in the past put a hook there to strap down some cargo and it messed the lip up. What you see here is 3 good coats of PPG’s Vibrance line high build epoxy. We sanded and cleaned the metal multiple times to ensure the surface was as clean as possible. Paul then applied the primer allowing the product to dry in between coats. The next step for these panels will be a good blocking out with 80 grit. We will then be able to see all of our low and high spots. We will do our body work right over this product. Once they are straight, another coat of epoxy followed by several coats of urethane high build primer. These are the most important steps in the paint process.

New job in the shop

DSCF0868DSCF0869DSCF0870DSCF0886DSCF0887DSCF0879DSCF0882DSCF0883DSCF0881Here are a few parts that were dropped off last week for a 1971 C10. We will be performing a full High Performance Finish on this truck. There will be several custom touches done on this one. The molding holes and side marker lights have all ready been welded up so we don’t have to worry with that. We did use our stud gun to weld studs to the low places so we can pull them back into shape to minimize the amount of filler needed to straighten out the dents. We also used a hammer and dolly to smooth out the dents as well. The next step will be to sand the bed inside and out and spray several coats of our high build epoxy primer. Stay tuned to this one. It should really stand tall.

%d bloggers like this: