Shoebox gets booth time.
It’s been very busy around the shop for the past few weeks. We have had tons of collision repairs which hasn’t left us much time to work on the restoration cars. We did manage to squeeze in a few hours here and there to get these parts ready for paint and while we were waiting on parts we we decided it was the perfect time to spay them. I’m not sure it this is an actual factory color, the owner had already picked this color before we started the project but I do really like it. We started with a coat of sealer followed by 3 coats of DBC base coat and 2 coats PPG’s 2021 clear. The body work on the rest of the car is coming along great hopefully we can get into the booth soon.
Time to shine!
Its been a long time coming but we are finally spraying some color on the C-10 project. We had intentions on painting both bedsides today but when we were prepping them, we found a spot on one of them that wasnt up to snuff. So it came back out for repair and we slid the radiator support in in its place. These parts were sealed with PPG’s urethane sealer followed by 3 coats of PPG base coat then 3 coats of clear. Things went smoothly and the turned out very nice. The color looks amazing. We will wet sand and buff the outside of the bedside before reassembly. Hopefully we will get another batch of parts painted in the next couple of weeks.
After a few good days of prepping the floor and bottom of the cab we were finally able to spray it. The first couple of pictures show how not prepping panels properly turn out. The black peeling paint is actually POR 15. It was improperly applied so we removed it before applying our coatings over it. We started with a coat of PPG’s DPLV epoxy primer over the bare metal and properly prepared panels. We actually did that yesterday afternoon. This morning we came in applied SEM seam sealer to the seams and the weld areas where patches were installed. Once the seam sealer was dry, Jordan sprayed 2 coats of Raptor liner over the DP. This well provide a water proof barrier for the under side of this truck that will still look very nice. While we were at it, we also sprayed the inside of the bedsides that are exposed to the bottom of the truck. Up next, its time to start spraying some panels while we finish up the body work on the cab.
Still plugging away on the C-10. Last week we finished up the body work on the cab and applied a couple more coats of PPG’s high build epoxy. Because the body work was so extensive we will definitely block that out and prime it again to be sure we didnt miss anything. Today we started prepping bottom of the cab for bedliner. As you can see it was blasted giving us a good starting point. You can see there are new patches in the floors in the top corners. Those areas were a little thin and the cab mounts needed to be shored up some as well. While Jordan sanded the bottom, Paul got a great start on straightening out the rockers. We still have a bit of sanding to do on the floor and more work on the rockers but over the next couple of days we should be able to get the bottom of the cab sprayed with epoxy followed by a couple coats of Raptor liner.
Progress on the Beetle is moving along. We have the fenders bolted down with new fender beading. The German running boards are on and looking really nice and the door glass is all in and functional. We have also removed the old exhaust system in preparation for the new one that is on its way. We also cleaned the engine up some while we were at it. The new turn signals are on and wired up as well as the head lights. We have also installed the new triple plated front bumper after we sandblasted the original brackets and repainted them semi gloss black. This one is really shaping up and it wont be long till its off the upholstery shop to get a new head liner.
After many hours of blocking a filling, the cab on the C-10 is pretty close to being straight. Yes, this one lived the life of a truck but glory days are in its future. With all the body work fairly close to being finished we will next turn our attention to the floor and bottom of the cab. Just like the rest of the underside on this truck it will get a bedliner both inside and out. We will then once more make sure the bodywork is complete before priming. Because of the extensive body work, we will most likely prime it twice to be sure its good to go.
Prime time ’55
We shot a few coats of primer on the ’55 hood and trunk today. As you can see they were in pretty good shape. We did have a few places that needed some attention but once they were straight and the booth was open, we slid them on in. These parts will be blocked one more time to be sure they are ready for paint. Its a long process but it really pays off in the end.
Just hanging around
The ’57 is getting its doors. After installing the door and trunk rubber we are ready to get these back on where they should feel right at home. Lining up the left door went pretty smoothly. We still have some fine tuning before moving to the other side. We will be installing the latches and catches once we are happy with the fitment.
Its a Bug again
All hands on deck
Great progress was made on the C-10 project today. Cole and I worked a good portion of the day blocking out the roof and fixing dents. We worked some on the inside of the cab as well as the left door jamb. The fire wall is pretty close to being finished as well. Tomorrow we plan on attacking it like we did today and hopefully that will put us pretty close to priming it again.